STANDARD RIGGING FEATURES INCLUDE:

TELEFLEX QC HELM BEZEL AND STEERING WHEEL
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN, KEY
5 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
50 GALLON CUSTOM ALUMINUM NMMA CERTIFIED FUEL TANK
CUSTOM FUEL SPILL VENT FOR DRAINAGE AWAY FROM PAINT
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
BILGE BLOWER
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
DRIVER CONSOLE WINDSHIELD
SILENT SYSTEMS EXHAUST MUFFLERS
BATTERY BOX (NO BATTERY)
NO SEAT OR BENCH TOPS
LARGE PORT SIDE GLOVE BOX WITH DOOR



STANDARD HULL FEATURES INCLUDE:
22' L.O.A. 86" BEAM, 72" 12 DEGREE BOTTOM
MULTI-STRAKES, DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
FORWARD FRONT 5 WINDOW SPLIT WALK THRU SYSTEM
PRE-FLEXED EXTRUDED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** INDMAR PORT FUEL INJECTED 5.7 RAW WATER ENGINE **
** AMERICAN TURINE SD-309 JET PUMP WITH "A" IMPELLER **
20'4" LONG x 72" WIDE, 0.250" THICK, 12 DEGREE REAR SECTION (5052)
0.190" 5052 BOW SECTIONS, 0.125" REINFORCED 5052 ONE PART SIDE MATERIALS
FIVE LONGITUDINAL STRINGERS, 1/4" CENTER, INVERTED COMPOUND "S" INNER
RAILS & 1/4" OUTTER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
32" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED TO SIDE SWIM DECK (22" L.O.A.)
4 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
DROP FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
DUAL SPLIT CONSOLE WITH D.O.T. 2 TINTED SAFTY GLASS
FLUSH REAR DECK / MOTOR COVER (NO HUMP) WITH GAS LIFT
SELF BAILING FRONT CASTING DECK
FRONT ANCHOR STORAGE WELL
COMPLETE SPRAY LINER INTERIOR,DECKS & SWIM DECK
SPRAY LINER ON GUNNEL TOP DOWN TO OUTER SOFT BODY LINE
D.O.T. 2 TINTED SAFETY GLASS, NO INTERIOR CARPET
ADDITIONAL X-LARGE TWIN REAR STORAGE COMPARTMENTS
LOCKING LATCHES ON LARGE DOORS
PUMP CLEANOUT ON EXTERIOR OF HULL
FULL LENGTH STRUCTURAL SIDE TRAY BRACE
TWO CUP HOLDERS
FRONT & REAR DECK PIN MOUNTS (TWO)
CHROME VENTURI COVERS
NO SEATS

Boat Models

Blazer

Blazer boats - custom built to order

Blazer boats are available in a wide variety of configurations.  These are all custom built,
call us for more details and configuration options -   Contact Page

1/6

Rapture II

STANDARD RIGGING FEATURES INCLUDE:

BAYSTAR HYDRAULIC STEERING (MAX 150 HP RATING)
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN KEY
6 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
30 GALLON BELLY FUEL TANK WITH SENDER, FILL & DUAL VENTS
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
550 GPH LIVE WELL AREATOR SYSTEM
FRONT TROLLING PANEL WITH PLUG AND DUAL BATTERY HARNESS SYSTEM
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO HI-BACK COLOR MATCHED SEATS
FIVE STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
TWO TRANSDUCER MOUNTS ON TRANSOM
REMOVEABLE COCKPIT SEATING
DRIVER CONSOLE WINSHIELD



STANDARD HULL FEATURES INCLUDE:

22' L.O.A. 94" BEAM, 72" BOTTOM
MULTI-STRAKES, DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
PRE-FLEXED FORMED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** U.S.G.C. INSPECTED & APPROVED 1100 LBS CAPACITY RATING**
** U.S.G.C. INSPECTED & APPROVED 150 HORSEPOWER RATING**
72" WIDE, 0.190" THICK, 16 DEGREE, 5052 H-34 ONE PART PAD BOTTOM
NOTCHED, STEPPED & VENTILATED MOTOR POD (0.190")
INVERTED COMPOUND "S" LONGITUDINAL STRINGER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
24" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED SWIM DECK
20" SHAFT LENGTH WITH FLOTATION POD AND SWIM DECK BRACING
2 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
60"FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
DUAL FRONT BATTERY MOUNTING BRACKET
48" REAR CASTING DECK COMES WITH 125 GALLON AERATED LIVE WELL
LARGE REAR STORAGE COMPARTMENT AND STORAGE BAY
ADDITIONAL TWIN TACKLE REAR STORAGE COMPARTMENT
25 GALLON FRONT LIVE WELL / ANCHOR BOX
SINGLE STARBOARD SIDE CONSOLE (WITH WINDSHIELD)
SPRAYED GUNNEL TOPS & INTERIOR WITH MILITARY GRADE BED LINER
COLORS: RED, GRAY, OLIVE GREEN, DESERT SAND
LONGITUDINAL STRUCTURAL SIDE BRACES / TRAYS
COCKPIT SIDE TRAYS
TWO CUP HOLDERS

Rapture III

STANDARD RIGGING FEATURES INCLUDE:

TRANSOM WARRANTY IS 10 YEARS
TELEFLEX QC HELM BEZEL AND STEERING WHEEL
6 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
12 GALLON SIDE FUEL TANK WITH SENDER, FILL & VENTS
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
550 GPH LIVE WELL AREATOR SYSTEM
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO HI-BACK COLOR MATCHED SEATS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
TWO TRANSDUCER MOUNTS ON TRANSOM
DRIVER CONSOLE WINSHIELD
PORT SIDE TRAY STORAGE
STAR SIDE TRAY STORAGE



STANDARD HULL FEATURES INCLUDE:

20' L.O.A. 76" BEAM, 56" FLAT BOTTOM
3 STEP NON STRETCHING PRESSED KEEL STRAKES FOR MERCURY 60/40 JET ONLY
PRE-FLEXED FORMED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** U.S.G.C. INSPECTED & APPROVED 750 LBS CAPACITY RATING**
** U.S.G.C. INSPECTED & APPROVED 60 HORSEPOWER RATING**
56" WIDE, 0.125" THICK, FLAT , 5052 H-34 TWO PART PAD BOTTOM
22" CUSTOM TRANSOM FOR JET ONLY APPLICATIONS
INVERTED COMPOUND "S" STRINGER X BRACEING SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
22" HIGH, 0.100" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" SPLIT INTEGRATED SWIM DECK
27" SHAFT LENGTH WITH CUSTOM INTAKE PUMP
7 @ 0.125" THICK LONGITUDINAL KEEL STRAKES
60"FRONT CASTING DECK WITH STORAGE COMPARTMENT
FRONT FOAM FLOTATION
48" REAR CASTING DECK COMES WITH 40 GALLON AERATED LIVE WELL
12 GALLON NMMA PERMENANT FUEL TANK WITH SENDER
REAR CENTER SECTION STORAGE BAY
ADDITIONAL REAR TWIN TACKLE REAR STORAGE COMPARTMENTS
25 GALLON FRONT LIVE WELL / ANCHOR BOX
SINGLE STARBOARD SIDE CONSOLE (WITH WINDSHIELD)
SPRAYED GUNNEL TOPS & INTERIOR WITH MILITARY GRADE BED LINER
COLORS: RED, GRAY, OLIVE GREEN, DESERT SAND
LONGITUDINAL STRUCTURAL SIDE BRACES / TRAYS
COCKPIT SIDE TRAYS
RE-INFORCED BOW SEAM
U.S.C.G. FLOTATION REQUIREMENTS FOR 750 LB CAPACITY

1/8

Rapture IV

STANDARD RIGGING FEATURES INCLUDE:

TELEFLEX QC HELM BEZEL AND STEERING WHEEL
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN, KEY
5 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
50 GALLON CUSTOM ALUMINUM NMMA CERTIFIED FUEL TANK
CUSTOM FUEL SPILL VENT FOR DRAINAGE AWAY FROM PAINT
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
550 GPH LIVE WELL AREATOR SYSTEM
BILGE BLOWER
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
DRIVER CONSOLE WINDSHIELD
SILENT SYSTEMS EXHAUST MUFFLERS
BATTERY BOX (NO BATTERY)



STANDARD HULL FEATURES INCLUDE:

22' L.O.A. 94" BEAM, 72" BOTTOM
MULTI-STRAKES, DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
PRE-FLEXED FORMED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** U.S.G.C. INSPECTED & APPROVED 1100 LBS CAPACITY RATING**
** U.S.G.C. INSPECTED & APPROVED 150 HORSEPOWER RATING**
72" WIDE, 0.190" THICK, 16 DEGREE, 5052 H-34 ONE PART PAD BOTTOM
NOTCHED, STEPPED & VENTILATED MOTOR POD (0.190")
INVERTED COMPOUND "S" LONGITUDINAL STRINGER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
24" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED SWIM DECK
20" SHAFT LENGTH WITH FLOTATION POD AND SWIM DECK BRACING
2 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
60"FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
DUAL FRONT BATTERY MOUNTING BRACKET
48" REAR CASTING DECK COMES WITH 125 GALLON AERATED LIVE WELL
LARGE REAR STORAGE COMPARTMENT AND STORAGE BAY
ADDITIONAL TWIN TACKLE REAR STORAGE COMPARTMENT
25 GALLON FRONT LIVE WELL / ANCHOR BOX
SINGLE STARBOARD SIDE CONSOLE (WITH WINDSHIELD)
SPRAYED GUNNEL TOPS & INTERIOR WITH MILITARY GRADE BED LINER
COLORS: RED, GRAY, OLIVE GREEN, DESERT SAND
LONGITUDINAL STRUCTURAL SIDE BRACES / TRAYS
COCKPIT SIDE TRAYS
TWO CUP HOLDERS



1/6

Rapture V

STANDARD RIGGING FEATURES INCLUDE:

TELEFLEX QC HELM BEZEL AND STEERING WHEEL
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN, KEY
5 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
50 GALLON CUSTOM ALUMINUM NMMA CERTIFIED FUEL TANK
CUSTOM FUEL SPILL VENT FOR DRAINAGE AWAY FROM PAINT
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
550 GPH LIVE WELL AREATOR SYSTEM
BILGE BLOWER
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
DRIVER CONSOLE WINDSHIELD
SILENT SYSTEMS EXHAUST MUFFLERS
BATTERY BOX (NO BATTERY)



STANDARD HULL FEATURES INCLUDE:

22' L.O.A. 94" BEAM, 72" BOTTOM
MULTI-STRAKES, DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
PRE-FLEXED FORMED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** U.S.G.C. INSPECTED & APPROVED 1100 LBS CAPACITY RATING**
** U.S.G.C. INSPECTED & APPROVED 150 HORSEPOWER RATING**
72" WIDE, 0.190" THICK, 16 DEGREE, 5052 H-34 ONE PART PAD BOTTOM
NOTCHED, STEPPED & VENTILATED MOTOR POD (0.190")
INVERTED COMPOUND "S" LONGITUDINAL STRINGER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
24" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED SWIM DECK
20" SHAFT LENGTH WITH FLOTATION POD AND SWIM DECK BRACING
2 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
60"FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
DUAL FRONT BATTERY MOUNTING BRACKET
48" REAR CASTING DECK COMES WITH 125 GALLON AERATED LIVE WELL
LARGE REAR STORAGE COMPARTMENT AND STORAGE BAY
ADDITIONAL TWIN TACKLE REAR STORAGE COMPARTMENT
25 GALLON FRONT LIVE WELL / ANCHOR BOX
SINGLE STARBOARD SIDE CONSOLE (WITH WINDSHIELD)
SPRAYED GUNNEL TOPS & INTERIOR WITH MILITARY GRADE BED LINER
COLORS: RED, GRAY, OLIVE GREEN, DESERT SAND
LONGITUDINAL STRUCTURAL SIDE BRACES / TRAYS
COCKPIT SIDE TRAYS
TWO CUP HOLDERS

STANDARD RIGGING FEATURES INCLUDE:

TELEFLEX QC HELM BEZEL AND STEERING WHEEL
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN, KEY
5 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
50 GALLON CUSTOM ALUMINUM NMMA CERTIFIED FUEL TANK
CUSTOM FUEL SPILL VENT FOR DRAINAGE AWAY FROM PAINT
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
550 GPH LIVE WELL AREATOR SYSTEM
BILGE BLOWER
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
DRIVER CONSOLE WINDSHIELD
SILENT SYSTEMS EXHAUST MUFFLERS
BATTERY BOX (NO BATTERY)



STANDARD HULL FEATURES INCLUDE:
22' L.O.A. 86" BEAM, 66" 8 DEGREE BOTTOM

MULTI-STRAKES, NOTCHED DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
PRE-FLEXED EXTRUDED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** INDMAR PORT FUEL INJECTED 5.7 RAW WATER ENGINE **
** AMERICAN TURINE SD-309 JET PUMP WITH "A" IMPELLER **
20'4" LONG x 66" WIDE, 0.190" THICK, 8 DEGREE, 5052 ONE PART PAD BOTTOM
0.125" REINFORCED 5052 SIDE MATERIAL
INVERTED COMPOUND "S" LONGITUDINAL STRINGER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
24" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED TO SIDE SWIM DECK (22" L.O.A.)
4 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
60" FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
SINGLE STAR SIDE CONSOLE (NO COVERING) WITH WINDSHIELD
FLUSH CARPETED REAR DECK (NO HUMP) WITH GAS LIFT
60" CARPETED FRONT CASTING DECK
FRONT 45 GALLON AERATED LIVE WELL
LARGE CARPETED FRONT STORAGE COMPARTMENT WITH GAS LIFT
INTERIOR CARPET (GRAY)
ADDITIONAL X-LARGE TWIN REAR STORAGE COMPARTMENT
LOCKING LATCHES ON LARGE DOORS
PUMP CLEAN OUT ON EXTERIOR OF HULL
FULL LENGTH STRUCTURAL SIDE BRACES
COCKPIT SIDE TRAYS
TWO CUP HOLDERS
FRONT & REAR DECK PIN MOUNTS (TWO)
CHROME VENTURI COVERS
NO PAINT, NO SEATS

1/4

Rapture VI

Rapture VI

STANDARD RIGGING FEATURES INCLUDE:

TELEFLEX QC HELM BEZEL AND STEERING WHEEL
MEP SOFT CONSOLE WITH TACH, OIL, H2O, VOLT, HOUR, FUEL, HORN, KEY
5 SWITCH ACCESSORY PANEL WITH EXTRA WIRING FOR FUTURE OPTIONS
50 GALLON CUSTOM ALUMINUM NMMA CERTIFIED FUEL TANK
CUSTOM FUEL SPILL VENT FOR DRAINAGE AWAY FROM PAINT
550 GPH BILGE PUMP WITH AUTOMATIC FLOAT (FUSED HOT)
BILGE BLOWER
NAVIGATION & ANCHOR LIGHTS WITH APPROPRIATE POLES
3/8" WELD ON BOW EYE AND TWO SINGLE HOLE TRANSOM TIE-DOWNS
TWO STAINLESS STEEL SEAT PIN MOUNTS
TROLL MOTOR REINFORCEMENT PLATE PORT SIDE
DRIVER CONSOLE WINDSHIELD
SILENT SYSTEMS EXHAUST MUFFLERS
BATTERY BOX (NO BATTERY)
NO SEAT OR BENCH TOPS
LARGE PORT SIDE GLOVE BOX WITH DOOR



STANDARD HULL FEATURES INCLUDE:
22' L.O.A. 86" BEAM, 72" 12 DEGREE BOTTOM
MULTI-STRAKES, DELTA PAD, REVERSE CHIN, HYDRO-DYNAMIC BOTTOM (MSDPRC)
FORWARD FRONT 5 WINDOW SPLIT WALK THRU SYSTEM
PRE-FLEXED EXTRUDED GUNNELSIDES, LONGITUDNAL STRINGER STRUCTURE
** INDMAR PORT FUEL INJECTED 5.7 RAW WATER ENGINE **
** AMERICAN TURINE SD-309 JET PUMP WITH "A" IMPELLER **
20'4" LONG x 72" WIDE, 0.250" THICK, 12 DEGREE REAR SECTION (5052)
0.190" 5052 BOW SECTIONS, 0.125" REINFORCED 5052 ONE PART SIDE MATERIALS
FIVE LONGITUDINAL STRINGERS, 1/4" CENTER, INVERTED COMPOUND "S" INNER
RAILS & 1/4" OUTTER SYSTEM
COCKPIT FLOOR X-BRACE =10" MAX.DISTANCE BETWEEN BRACES
32" HIGH, 0.125" THICK PRE-FLEXED FORMED GUNNEL SIDES
20" FULL WIDTH INTEGRATED TO SIDE SWIM DECK (22" L.O.A.)
4 @ 0.190" THICK LONGITUDINAL LIFTING STRAKES
DROP FRONT CASTING DECK WITH LARGE STORAGE COMPARTMENT
DUAL SPLIT CONSOLE WITH D.O.T. 2 TINTED SAFTY GLASS
FLUSH REAR DECK / MOTOR COVER (NO HUMP) WITH GAS LIFT
SELF BAILING FRONT CASTING DECK
FRONT ANCHOR STORAGE WELL
COMPLETE SPRAY LINER INTERIOR,DECKS & SWIM DECK
SPRAY LINER ON GUNNEL TOP DOWN TO OUTER SOFT BODY LINE
D.O.T. 2 TINTED SAFETY GLASS, NO INTERIOR CARPET
ADDITIONAL X-LARGE TWIN REAR STORAGE COMPARTMENTS
LOCKING LATCHES ON LARGE DOORS
PUMP CLEANOUT ON EXTERIOR OF HULL
FULL LENGTH STRUCTURAL SIDE TRAY BRACE
TWO CUP HOLDERS
FRONT & REAR DECK PIN MOUNTS (TWO)
CHROME VENTURI COVERS
NO SEATS

Rapture VII

R & L

Marine

 

Copyright 2012 R&L Marine